OK on sizing I measured the length as described and pulling the 1/4" paper snugly I measure 9"...does that sound correct. I don't want a oversized ring but nervous about getting to large a one.

Chris

Well, Ron Jeremy wears a 2" comfortably, so you must be one HUGE guy. Try the largest diameter (in any style) and, if it's too small, return it for a full refund.

We had the same issue. Ranger started out with a 1 7/8 which can be a little tight at times, so we went to a 2" when we got his Charcoal Master. It fits perfectly.

I keep wondering if we didn't measure differently than we're supposed to. Even though we followed instructions perfectly!

~Ang

Well I took Ketch's advice and visited the local hardwear and 2" brass ring REALLY did the trick...so I put a photo of what I want for X-mas on my wife's desk...hope Christmas comes early. Thanks for all the help. smitty

I had an initial sizing problem as well. First tried a 1-7/8....OUCH - get it off!

I then tried a 2" ring, and it's fine & dandy, as well as my favorite sexual accoutrement, if you will. Tons of fun and pleasure - for the both of us.

I must have measured a dozen times, each time measuring about 2 1/2" - just larger than Gear Essentials makes. I finally chanced an order on the .4" Titan 2 1/4" and while i'd say it fits, it is not as snug as I'd like during... Uh... Playtime. Maybe measuring with string would yield a more accurate result than a paper strip, which was difficult (for me) to manage.

Next time I'll order the 2" ring, but for now I'm very happy with the Titan .4" and posted a pic here: Ring Thread

Cheers!

Yeah - that Titan looks nice - and you wear it well dude. I may have to give Freddy's online shop a jingle.

Also you can get very inexpensive aluminum rings in various anodized colors at JT's Stockroom.
http://www.stockroom.com/

I just ordered a cock ring for my boyfriend. First I measured him. (He couldn't figure out what I was measuring for. I want to surprise him.) I followed the directions exactly and have now done it quite a few times. Each time the measurement is 8"+. That seems so big though. When I divide it by 3, I came up with 2.66. He is big in girth, but does that sound right?

As I posted already on another thread........

the cock ring came in time to give him for Christmas. Sure enough, even though I ordered the largest size at 2.25", it's not quite big enough. He has tried it twice now for me. It works, but he said he is a little sore afterwards. My goodness, what a beautiful specimen he is though. I got him to let me take some pics.

So, you have measured twice and ordered your ring from F&E. I arives in the mail.
Now what? How does this thing get on?

Here is how.

1. First of all Relax!!! make sure your scrotum is warm and relaxed. You will have a heck of a time if the boys are held close to the body.
You will notice that one of your testicles hangs a bit lower than the other.



Now grasp the ring in one hand and place it below your scrotum.



Now reach up and and grasp the skin with your fingers. GENTLY pull that lower testicle through the ring while holding the ring with your other hand.



One testicle will fall though the hole in the ring along with the skin.



Now reach up through the hole again and grasp the skin just below your testicle that has not gone through the ring. Usualy the second one will follow the first.



Once both are though you can snug the ring up so that is settled at the base of your peinis.



You can now feed your penis though the ring. Do this by creating a space with your finger and then feed the glands (head) through the ring.



Gently pull the rest of your penis though the hole and adjust until comfortable.



Congratulations, you have put on your new cock ring!

Enjoy!

This message has been edited. Last edited by: Northern Nurse,

I just today received a 2" barbwire engraved Imperial (thanks Freddy) and this thing is awesome and fits well (so far).

One thing I ended up doing for sizing that I'd like to recommend...

I ended up buying an adjustable hose clamp in about a 2 1/4" size. These are available at any hardware store and are adjustable so you can try actual sizes out without having to go through O-rings (that flex). I used a 6" steel ruler to measure the diameter for 2" and then tried 2 1/8". The 2" fit best. The hose clamp is about 1/2" in width, so it is about the same width as many rings are.

You just need to be a bit careful placing yourself in one. What's cool is you can get hard while trying it out and if it is the wrong size, just adjust away. You can go from the smallest size to the largest with the same clamp.

Wow, I would immageing that it would cut in a bit when you were getting erect.

In theory it sounds great. I wonder if they have sutch an Aviation Clamp for plastic or PVC.
Less sharp edges for you to pinch on

Great manual, Northern.
I still have my foreskin and so use that to feed my penis through. Otherwise, same method as you.

a larger zip tie could also be used. just remove the locking tab so you can get it back off. put it in place, adjust for the fit thats best limp and erect,mark with a felt tip pen, and measure.

Grump,
I figured it was about time. This way when we get the "how do you" we can just send the link.

Ketch,

Great idea